Curzing home from work tonight, and went to change gear as I normaly do (not racing or anything, just a normal upshift) put the clutch peddle in, and now wont come out. The only bit of luck was I was only 500m from home.
I have had a look at the master cyclinder, and the oil lines, and everything appares to be OK, the slave cyclinder is mounted as it should be, and the leaver the the slave cyclinder pushes appares to be free enough (not too sure if it is too free or not)
What else can I check? Or is it a split box/engine time?
Thanks
Neil
Clutch peddle wont go out :(
Moderator: The Mod Squad
5 posts
• Page 1 of 1
Clutch peddle wont go out :(
by Corona » Fri Jul 29, 2005 7:52 pm
Just remember: The glass is neither half full nor half empty, it is merely the wrong size
-
Corona - Toyspeed Member
- Posts: 187
- Joined: Tue Mar 16, 2004 8:34 am
- Location: North Shore, Auckland
Re: Clutch peddle wont go out :(
by Loudtoy » Fri Jul 29, 2005 8:05 pm
Corona wrote:Curzing home from work tonight, and went to change gear as I normaly do (not racing or anything, just a normal upshift) put the clutch peddle in, and now wont come out. The only bit of luck was I was only 500m from home.
I have had a look at the master cyclinder, and the oil lines, and everything appares to be OK, the slave cyclinder is mounted as it should be, and the leaver the the slave cyclinder pushes appares to be free enough (not too sure if it is too free or not)
What else can I check? Or is it a split box/engine time?
Thanks
Neil
Drain the fluid out of it and have a proper look at the master cylinder, this is the case in about 90% of situations like this, something possible but would be very strange if it happened would be that the clutch pedal return spring let go, very very strange.
If you can pull your pedal up and it falls straight back down again i would say that the push rod has seperated from the the seal type thing that pushes the fluid in, seen it happen before! So clutch is permantently depressed sort of feeling!
TS Member sine 2001
Prado To tow stuff with
NZ Ae82 GT Liftback for gravel fun
Rodeo to do work stuff in
Big Ass Trailer to put stuff on
Car no 16 in a long line of less than ilustrious automobiles
Prado To tow stuff with
NZ Ae82 GT Liftback for gravel fun
Rodeo to do work stuff in
Big Ass Trailer to put stuff on
Car no 16 in a long line of less than ilustrious automobiles
-
Loudtoy - Toyspeed Member
- Posts: 1833
- Joined: Tue Jun 04, 2002 9:26 pm
- Location: In a ditch, watch for triangle!!
by method » Fri Jul 29, 2005 8:40 pm
clutch release bearing? 
PICS UPDATED DAILY
Evo IV - 13.0 @ 167.8 kph Full street trim - SOLD
Boosted 4age Ke30 - Im back and better than ever!
Evo IV - 13.0 @ 167.8 kph Full street trim - SOLD
Boosted 4age Ke30 - Im back and better than ever!
-
method - Toyspeed Member
- Posts: 1466
- Joined: Thu Jul 01, 2004 5:58 pm
- Location: West Auckland
Re: Clutch peddle wont go out :(
by Corona » Sat Jul 30, 2005 1:02 am
Loudtoy wrote:If you can pull your pedal up and it falls straight back down again i would say that the push rod has seperated from the the seal type thing that pushes the fluid in, seen it happen before! So clutch is permantently depressed sort of feeling!
Yea, basicaly thats whats hapening. I'll have a look at it tomorrow, and see what I can do
Just remember: The glass is neither half full nor half empty, it is merely the wrong size
-
Corona - Toyspeed Member
- Posts: 187
- Joined: Tue Mar 16, 2004 8:34 am
- Location: North Shore, Auckland
by Crimson Tears » Sat Jul 30, 2005 3:09 pm
Pull back the seal on the clutch slave cylinder and see if it is full of fluid. The seals in the slave cylinder may have gone.
- Crimson Tears
- Toyspeed Member
- Posts: 307
- Joined: Thu Sep 19, 2002 12:51 am
- Location: Christchurch
5 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 8 guests