5 Stud conversion??
Moderator: The Mod Squad
12 posts
• Page 1 of 1
5 Stud conversion??
by soopachargen » Tue Aug 29, 2006 8:43 pm
Is it possible to change a fwd corolla to 5 stud using maybe camry or corona "hubs"?? Are the suspension arms etc similar enough that it would be feasible to swap the hubs over?? I'm not asking if its logical... or saying should i do it... jst can i do it?
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
by wde_bdy » Tue Aug 29, 2006 9:09 pm
That GT4 converted EE90 Corolla that Ezy10s was selling was 5 stud. Not sure how it was done but might be worth looking at.
http://forums.toyspeed.org.nz/viewtopic.php?t=44911&highlight=
Callum
http://forums.toyspeed.org.nz/viewtopic.php?t=44911&highlight=
Callum
-
wde_bdy - Toyspeed Member
- Posts: 2704
- Joined: Wed Oct 23, 2002 11:43 pm
- Location: Gisborne
by soopachargen » Tue Aug 29, 2006 9:38 pm
strx7 wrote:see my responce in that thread.
i investigated it on my mates AE92, trying to build some un blowable front axles/hubs etc
just for ease of use could u post that here aswell??
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
by strx7 » Tue Aug 29, 2006 9:47 pm
i'd say the drive flanges from the celica fit straight into the hub carrier of the celica if you use ALL the celica bearing in them. I know V6 Camry 5 stud 5 x 114.3 drive flanges can be done that way. toyota are sooo good when it comes to interchanging things
Online Car Forums - Where Hui seems to take preference over Do-ey
HDJ81- 112AWKW @ 10psi), FC3S (Tarmac Spec 335rwhp@11psi), 3SGTE stroker - replacement body found.
Motorsport Bay of Plenty - http://www.mbop.org.nz
HDJ81- 112AWKW @ 10psi), FC3S (Tarmac Spec 335rwhp@11psi), 3SGTE stroker - replacement body found.
Motorsport Bay of Plenty - http://www.mbop.org.nz
- strx7
- Toyspeed Member
- Posts: 3707
- Joined: Mon May 24, 2004 12:06 am
- Location: Tauranga
by soopachargen » Tue Aug 29, 2006 9:53 pm
would the corolla driveshafts work?
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
by strx7 » Tue Aug 29, 2006 10:22 pm
if you used V6 or Celica flanges then no, cause they run the BIG outer CV joints which run the largest spline size, if you however used St170/St190 corona 5 x 100 hubs they run smaller CV's/Splines and i THINK they are the same size as corolla.
- strx7
- Toyspeed Member
- Posts: 3707
- Joined: Mon May 24, 2004 12:06 am
- Location: Tauranga
by soopachargen » Tue Aug 29, 2006 10:24 pm
i wonder if the big cvs are the same size as gze ones?
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
by strx7 » Tue Aug 29, 2006 10:36 pm
AE92 AGZE powered car has the EXACT same drive flanges as non AGZE powered cars, i'd therefore conclude that they runn smaller outer CV's that GT4's and V6 camry's.
Online Car Forums - Where Hui seems to take preference over Do-ey
HDJ81- 112AWKW @ 10psi), FC3S (Tarmac Spec 335rwhp@11psi), 3SGTE stroker - replacement body found.
Motorsport Bay of Plenty - http://www.mbop.org.nz
HDJ81- 112AWKW @ 10psi), FC3S (Tarmac Spec 335rwhp@11psi), 3SGTE stroker - replacement body found.
Motorsport Bay of Plenty - http://www.mbop.org.nz
- strx7
- Toyspeed Member
- Posts: 3707
- Joined: Mon May 24, 2004 12:06 am
- Location: Tauranga
12 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 11 guests