toyota recommends tightening(in sequence) to 22 ft lbs then another 90 degrees then another 90 degrees.
arp recommends that you use manufactuerers sequence but tighten to 60ft lbs instead. does that soundright?
arp headbolts, how do you get to them?
Moderator: The Mod Squad
8 posts
• Page 1 of 1
arp headbolts, how do you get to them?
by bluemaumau » Thu Feb 28, 2008 4:48 pm
new question added
toyota recommends tightening(in sequence) to 22 ft lbs then another 90 degrees then another 90 degrees.
arp recommends that you use manufactuerers sequence but tighten to 60ft lbs instead. does that soundright?
toyota recommends tightening(in sequence) to 22 ft lbs then another 90 degrees then another 90 degrees.
arp recommends that you use manufactuerers sequence but tighten to 60ft lbs instead. does that soundright?
Last edited by bluemaumau on Thu Feb 28, 2008 6:07 pm, edited 1 time in total.
4AGTE AE101 COROLLA - 90%
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
-
bluemaumau - Toyspeed Member
- Posts: 4087
- Joined: Sun Oct 16, 2005 7:08 pm
- Location: SYDNEY, NSW
by IH8TEC » Thu Feb 28, 2008 4:53 pm
they are talking about the sequence of the bolts,
DO NOT use any torque settings/90deg bs from toyota.
start at like 30 in the proper sequence, then go to like 45, then go over and go to 60.
DO NOT use any torque settings/90deg bs from toyota.
start at like 30 in the proper sequence, then go to like 45, then go over and go to 60.
Current Rides: 1994 Hiace Custom
KTM 250sx
Previous Car: 1988 Toyota Levin 4agte
234kw atw and 12.5@183kmh
Sold to a muppit who wrecked it
Hmm
KTM 250sx
Previous Car: 1988 Toyota Levin 4agte
234kw atw and 12.5@183kmh
Sold to a muppit who wrecked it
Hmm
-
IH8TEC - Toyspeed Member
- Posts: 3128
- Joined: Wed Nov 26, 2003 7:11 pm
by bluemaumau » Thu Feb 28, 2008 4:55 pm
ah cheers i confused myself 
to anxious
to anxious
4AGTE AE101 COROLLA - 90%
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
-
bluemaumau - Toyspeed Member
- Posts: 4087
- Joined: Sun Oct 16, 2005 7:08 pm
- Location: SYDNEY, NSW
by bluemaumau » Thu Feb 28, 2008 6:08 pm
ok so the heads on and beside the outside 4 i can get to the others with my 12mm socket, is there a special tool required?
from memory they only make 10mm deep sockets? -good memory or bad?
from memory they only make 10mm deep sockets?
-good memory or bad?4AGTE AE101 COROLLA - 90%
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
-
bluemaumau - Toyspeed Member
- Posts: 4087
- Joined: Sun Oct 16, 2005 7:08 pm
- Location: SYDNEY, NSW
by RunningRich » Thu Feb 28, 2008 6:45 pm
A Koken 3/8" deep socket in the correct imperial size (7/16"?) does the job perfect and fits past the cams. May cost around $12-$15.
Richard
Toyota Celica GT-Four Group A (sold)
Alfa Romeo 75 Twinspark (sold)
BMW 530i E61 Touring Motorsport
http://gtfour.supras.org.nz
Toyota Celica GT-Four Group A (sold)
Alfa Romeo 75 Twinspark (sold)
BMW 530i E61 Touring Motorsport
http://gtfour.supras.org.nz
-
RunningRich - Toyspeed Member
- Posts: 1044
- Joined: Mon May 27, 2002 1:46 pm
- Location: Auckland
by bluemaumau » Thu Feb 28, 2008 10:36 pm
okay thanks
4AGTE AE101 COROLLA - 90%
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
-
bluemaumau - Toyspeed Member
- Posts: 4087
- Joined: Sun Oct 16, 2005 7:08 pm
- Location: SYDNEY, NSW
by jaypines » Fri Feb 29, 2008 8:38 am
depends on the bolt... ARP recommends only the sequence from the manufacturer then apply their torque. while toyota recommends applying pre-load torque +90 +90. heres a good read about that: RV8
-
jaypines - Toyspeed Member
- Posts: 167
- Joined: Fri Jan 12, 2007 4:05 pm
8 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 25 guests