What then?
Im going into work today, it sounds like Ive got some more saving up to do.
bearings problem.
Moderator: The Mod Squad
90 posts
• Page 3 of 5 • 1, 2, 3, 4, 5
by fivebob » Mon Jan 30, 2006 2:47 pm
RomanV wrote:If I can get my hands on some decent measuring tools, I might see if I can measure it all up myself.
Probably not a good idea in this case. You're dealing with measurements in the 0.0001" area, and most micrometers lose accuracy at that point. Even with an accurate mic it takes a skilled operator to use it. I've got equipment that accurate, but I never let it out of my sight, and let few others use it as it's easily damaged if not used correctly, and to replace it I would have to start selling body parts
Cheaper equipment should be ok for gross errors in shell size or alignment, or if you just want to see if everything is in the right ballpark though (0.001").
-
fivebob - Toyspeed Member
- Posts: 3879
- Joined: Fri May 02, 2003 5:12 pm
- Location: Tauranga
by RomanV » Mon Jan 30, 2006 2:52 pm
Okay, fair enough.
Off to the workshop it is then.
Its concerning that you didnt say 'your own' body parts.
Off to the workshop it is then.
fivebob wrote: and to replace it I would have to start selling body parts
Its concerning that you didnt say 'your own' body parts.
-
RomanV - Toyspeed Member
- Posts: 4915
- Joined: Wed Aug 13, 2003 12:17 am
- Location: West Auckland
by RomanV » Mon Jan 30, 2006 7:08 pm
Why would I want to do that?
It makes less HP than the engine that I'm reassembling...
That one is only a 200hp version (despite what he says) And since it is from an auto, doesnt come with the extra goodies that make the blacktop better than the redtop.
And there's also the fact that it wont fit in an MR2, and it doesnt look as cool.
It makes less HP than the engine that I'm reassembling...
That one is only a 200hp version (despite what he says) And since it is from an auto, doesnt come with the extra goodies that make the blacktop better than the redtop.
And there's also the fact that it wont fit in an MR2, and it doesnt look as cool.
-
RomanV - Toyspeed Member
- Posts: 4915
- Joined: Wed Aug 13, 2003 12:17 am
- Location: West Auckland
by vvega » Mon Jan 30, 2006 8:11 pm
fivebob wrote:RomanV wrote:If I can get my hands on some decent measuring tools, I might see if I can measure it all up myself.
Probably not a good idea in this case. You're dealing with measurements in the 0.0001" area, and most micrometers lose accuracy at that point. Even with an accurate mic it takes a skilled operator to use it. I've got equipment that accurate, but I never let it out of my sight, and let few others use it as it's easily damaged if not used correctly, and to replace it I would have to start selling body parts
Cheaper equipment should be ok for gross errors in shell size or alignment, or if you just want to see if everything is in the right ballpark though (0.001").
as do i
had i of realised i could have bought some proper measurment tools up with me
we tried switching the shells
trided them in differnt journals (on using 2 at any time
and swaped between the 3's and the 4's
im back up again next week david if need be ill bring my digital mic's and internal bore guage
but in reality even with a simple interal tele guage you will be able to tell if the journal is out of round
- vvega
by RomanV » Mon Jan 30, 2006 9:14 pm
Yep, I'll still be pestering Lynn in the morning. 
However, taking it to him will be a last resort I think.
He does great work, but he is in such high demand, that it takes forever and a day to get anything done.
However, taking it to him will be a last resort I think.
He does great work, but he is in such high demand, that it takes forever and a day to get anything done.
-
RomanV - Toyspeed Member
- Posts: 4915
- Joined: Wed Aug 13, 2003 12:17 am
- Location: West Auckland
by RomanV » Mon Jan 30, 2006 9:21 pm
Well, thats what Ive heard too.
But His prices were reasonable for what I got done IMO.
More expensive than other places, but its worth knowing that it got done right, and its worth the extra $$$ for all of the experience that him and his cronies have with 3sg(t)e's, in my opinion.
He was more than helpful, patiently answered all of my stupid questions, and put up with more "is it done yet?" "Is it done yet?" than most people could take.
However, I suppose it is worth waiting to get it done right, than get it done half assed, and completely blow up my engine.
But His prices were reasonable for what I got done IMO.
More expensive than other places, but its worth knowing that it got done right, and its worth the extra $$$ for all of the experience that him and his cronies have with 3sg(t)e's, in my opinion.
He was more than helpful, patiently answered all of my stupid questions, and put up with more "is it done yet?" "Is it done yet?" than most people could take.
However, I suppose it is worth waiting to get it done right, than get it done half assed, and completely blow up my engine.
-
RomanV - Toyspeed Member
- Posts: 4915
- Joined: Wed Aug 13, 2003 12:17 am
- Location: West Auckland
by RomanV » Tue Jan 31, 2006 10:06 am
Well I gave Lynn a call this morning, and he sounded very surprised.
He said I should be able to bring it in tomorrow, for him to have a look at.
Hopefully it wont be anything too major!
He said I should be able to bring it in tomorrow, for him to have a look at.
Hopefully it wont be anything too major!
-
RomanV - Toyspeed Member
- Posts: 4915
- Joined: Wed Aug 13, 2003 12:17 am
- Location: West Auckland
90 posts
• Page 3 of 5 • 1, 2, 3, 4, 5
Who is online
Users browsing this forum: No registered users and 13 guests