Toyspeed.org.nz Message Board

by **SpeedRacer** » Tue May 16, 2006 3:18 pm

I know this is a long shot but here goes!

Converting my 4AGE bigport redtop to an ae101 4agze but turboed. my delima is that all the plugs are different (almost).

does anyone have any pics or anything to help me tell which plug goes where?

Its mostly alternator (was cut so I have to use 4age plugs), CAS, coils and ignitors. all the others i have figured.

thanks in advance

-Speed

by **SpeedRacer** » Tue May 16, 2006 3:52 pm

ok, so ive got some pics now

EDIT::scrolled down for good pics :wink:

thanx
-Speed

by **sergei** » Tue May 16, 2006 4:04 pm

can you make better pictures?
#7 A/C plug
#8 Cold start water temperature switch plug
#9 WTS plug
...
I think 1,2,3 should go in fuse box
#12 maybe knock sensor

by **NA Drifter** » Tue May 16, 2006 4:06 pm

I'll take 8 and 9 are water temp sensors that's behide the head? ..but i could be wrong..

If you go to maybe club4ag.com and look at the spec sheet wiring for the 4agze(if they have them) there should be some picture at the back ground showing the plug.

Else use a multi meter to trace the plug back to where is plug to the ecu and see which pin are they.

by **SpeedRacer** » Tue May 16, 2006 4:33 pm

cool thanx guys, any advances fo the others? i figured out 10 and 11 go to coil pack so that leaves 4, 5, 6, 12mayb, 13, 14, 15, 16

by **IH8TEC** » Tue May 16, 2006 4:37 pm

honestly if you can get better pics, could probably tell them all to you, bu some of them you can't tell sht

by **sergei** » Tue May 16, 2006 4:39 pm

If images were better I would identify all of them...

by **SpeedRacer** » Tue May 16, 2006 5:06 pm

k will go find another camera

by **SpeedRacer** » Tue May 16, 2006 5:52 pm

ok lets try this again

2,3,4,5 i just need to kno whr those pipes go

6 where do 6 and 7 go to/come from

8 has been cut and dont know where it came from

13 im thinking are the alternator wires but don't know about the little coloured ones

18 is the turbo pressure sensor(?) just need to know where that pipe goes (is it the same pipe as the na vac sensor?)

20 cut wire duno where it came from though

22 was cut also and im thinking its to the battery? same line as 3 plugs in bg and i think those are to the fuse box

tried to take them in order from gearbox side to pulley side.

thanx
-Speed

by **SpeedRacer** » Wed May 17, 2006 9:37 am

did i mention theres a chocy fish for the winner?

bump

by **Bazda** » Wed May 17, 2006 11:16 am

#19 is the tps
#23 is a idle up valve thinghy
#13 is for the alternator
#14 prob 12v, ignition on, alternator excitor wire(yellow)..

by **sergei** » Wed May 17, 2006 12:27 pm

11 Injector plug (cold start?)
23 ISCV (idle speed control valve)
19 TPS
6 - 7 AC idle up lines, one before and one after throttle body (order does not matter).
18 Goes to inlet manifold, same way as NA one, thorugh a damper.
15 AC pressure switches, one pair of those need to be shorted across to stop the fan going all the time.
22 Might go to fuse box.

Have you connected speed sensor plug? #19 is very similar, also #10 is similar to reverse switch.

by **SpeedRacer** » Sun May 21, 2006 12:28 am

any advances? I rekon im just going to cut the plug off the 4ag loom and attach it to the 4agz loom. good or bad idea? any advice?
anyone in or near palmy wanna give me a hand?

have entire loom and ecu for both

Toyspeed.org.nz Message Board

4agze wiring - Lets Play "GUESS THAT PLUG!"

4agze wiring - Lets Play "GUESS THAT PLUG!"

Who is online