1JZGTE Waterpump
Moderator: The Mod Squad
8 posts
• Page 1 of 1
1JZGTE Waterpump
by RickGT » Thu Aug 02, 2007 11:41 pm
Looking for a new waterpump to replace the hydraulic waterpump assy, tried a 2jzgte one and it doesnt line up, went to Toyota an they only list 1 pump for 1jzgte which is the hydraulic, but there is a listing for a 1jz-ge one that is just the water pump, would this fit onto 1jz-gte?
MX73 GLXi Cressida 1JZ-GTE
EP91 Glanza V
EP91 Glanza V
-
RickGT - Toyspeed Member
- Posts: 356
- Joined: Wed May 04, 2005 6:46 pm
- Location: Napier, Hawkes Bay
by spencer » Thu Aug 02, 2007 11:51 pm
my 1jzgte had a normal fan on it, used the repco listing for the pump bolted up fine. dont know if the 1jzge housing has the water lines that run around to the oil cooler
ms63 crown
- spencer
- Toyspeed Member
- Posts: 1328
- Joined: Wed Oct 22, 2003 1:33 pm
- Location: hamilton
by MrOizo » Fri Aug 03, 2007 9:56 am
I used the 2JZGTE pump (front and rear housings). You have to use a complete 2JZGTE setup (including the Pulley too)
Just make sure you sort a switch out for the electric fan if thats where you go of the viscous setup off the JZA80. I had a switch and kept forgetting it when i got into traffic and i could hear the 'kettle boil'
Just make sure you sort a switch out for the electric fan if thats where you go of the viscous setup off the JZA80. I had a switch and kept forgetting it when i got into traffic and i could hear the 'kettle boil'
-
MrOizo - Toyspeed Legend
- Posts: 6658
- Joined: Thu May 16, 2002 9:26 pm
- Location: Onehunga, Auckland
by postfach » Fri Aug 03, 2007 9:58 am
Non-Hydraulic water pump - Part Number 16100-49846
Non-Hydraulic water pump pulley - Part Number 16371-46020
They will tell you that those numbers aren't listed for any of the cars you might expect to get a 1JZ-GTE out of, but trust me, they are the right parts, I have them in my car. My pump came as a complete unit (minus the pulley, which is why I've supplied the part number for it) with all the seals etc that you would need.
It looks like this:
(click for bigger image)
Non-Hydraulic water pump pulley - Part Number 16371-46020
They will tell you that those numbers aren't listed for any of the cars you might expect to get a 1JZ-GTE out of, but trust me, they are the right parts, I have them in my car. My pump came as a complete unit (minus the pulley, which is why I've supplied the part number for it) with all the seals etc that you would need.
It looks like this:
(click for bigger image)
-
postfach - Toyspeed Member
- Posts: 2205
- Joined: Fri Apr 01, 2005 11:45 pm
- Location: North Shore, Auckland
by strx7 » Fri Aug 03, 2007 10:17 am
that looks like a run of the mill 2JZGE pump
Online Car Forums - Where Hui seems to take preference over Do-ey
HDJ81- 112AWKW @ 10psi), FC3S (Tarmac Spec 335rwhp@11psi), 3SGTE stroker - replacement body found.
Motorsport Bay of Plenty - http://www.mbop.org.nz
HDJ81- 112AWKW @ 10psi), FC3S (Tarmac Spec 335rwhp@11psi), 3SGTE stroker - replacement body found.
Motorsport Bay of Plenty - http://www.mbop.org.nz
- strx7
- Toyspeed Member
- Posts: 3707
- Joined: Mon May 24, 2004 12:06 am
- Location: Tauranga
by RickGT » Sat Aug 04, 2007 1:23 pm
postfach wrote:Non-Hydraulic water pump - Part Number 16100-49846
Non-Hydraulic water pump pulley - Part Number 16371-46020
They will tell you that those numbers aren't listed for any of the cars you might expect to get a 1JZ-GTE out of, but trust me, they are the right parts, I have them in my car. My pump came as a complete unit (minus the pulley, which is why I've supplied the part number for it) with all the seals etc that you would need.
It looks like this:
(click for bigger image)
Sweet cheers for that, gettin revhead to get me a price, but i had the number 16100-49845 but aparently doesnt show up on the system
MX73 GLXi Cressida 1JZ-GTE
EP91 Glanza V
EP91 Glanza V
-
RickGT - Toyspeed Member
- Posts: 356
- Joined: Wed May 04, 2005 6:46 pm
- Location: Napier, Hawkes Bay
8 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 22 guests