tie rod taper
Moderator: The Mod Squad
7 posts
• Page 1 of 1
tie rod taper
by soopachargen » Wed Jan 27, 2010 1:02 am
is the taper on all toyota tie rods the same? ie could an ae86 tie rod go into an ae101 upright??
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
by Mr Revhead » Wed Jan 27, 2010 8:39 am
Afraid not, a lot will be the same, but there are different tapers.
wtf are you upto?
wtf are you upto?
-
Mr Revhead - SECURITY!
- Posts: 24635
- Joined: Tue Jan 20, 2004 4:06 pm
- Location: Nelson
by soopachargen » Wed Jan 27, 2010 8:42 am
looking into making myself a "bumpsteer kit" for an excessively lowered ae101 with silly wheels, basically fixing geometry that I have ruined trying to get a look that I want
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
by Mr Revhead » Wed Jan 27, 2010 8:46 am
ah yep. Maybe drop into your friendly autolign/ripco/bnt etc with verniers and start going through some boxes
Or.... HPI Engineering in chch, they rebuild all ball joints. I am sure they could make custom ones
Or.... HPI Engineering in chch, they rebuild all ball joints. I am sure they could make custom ones
-
Mr Revhead - SECURITY!
- Posts: 24635
- Joined: Tue Jan 20, 2004 4:06 pm
- Location: Nelson
by soopachargen » Wed Jan 27, 2010 8:47 am
i was hoping to use an ae86 or s13 spherical rod end kit
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
by Burning Angel » Wed Jan 27, 2010 9:27 am
even if the dont fit you could get a new inserts turned up easily for the sperical bearing type.
1984 SRP61 Starlet
1999 WRX Type RA
1999 WRX Type RA
-
Burning Angel - Toyspeed Member
- Posts: 457
- Joined: Wed Aug 17, 2005 11:21 am
- Location: Dunedin
by soopachargen » Wed Jan 27, 2010 9:29 am
yeah that was the next option, otherwise i've been told by a ralliart tech to drill the taper out
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
7 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 6 guests