Radiator filter

[gt4dude]

Anyone know where to get the parts to make something like this?

http://www.jag-lovers.org/xj-s/book/CoolantFilters.html





I been around Mitre 10 and place makers couldn't find anything suitable, that website is a good read. I noticed my new radiator is getting blocked again and my temp is starting to rise, I'm sick of trying to flush my cooling system all the time

[limbo]

I was looking at getting one, they are not to expensive see my ealier post, from memory $60 AUD plus postage

Never ended up getting one tho.

http://forums.toyspeed.org.nz/viewtopic.php?t=85049&highlight=

[Mr Ree]

What is causing you new radiator to get blocked? I would look into curing that before adding the filter.

Is it a reaction between different coolants/water wetter? Electrolysis?

[Bling]

What is causing you new radiator to get blocked? I would look into curing that before adding the filter.

This^^

I don't see how a filter will help solve much.

[gt4dude]

Just bits of crud from this



that didn't come out with a garden hose along with whatever rust scale it took with it.

(To save the bullsh1t posting, yeah t-stat out, yeah reverse flush yada yada yada)

[Mr Ree]

And dont forget to reverse flush the heater core several times too

[DVSMOTORSPORT]

Just bits of crud from this



that didn't come out with a garden hose along with whatever rust scale it took with it.

(To save the bullsh1t posting, yeah t-stat out, yeah reverse flush yada yada yada)

Well theres your problem right there. Stuff using crap like that.

[allencr]

Water AND compressed air!!!!
Forward & reverse, no thermostat, engine, radiator & heater core.
Garden hose full on into inlet/outlet, rag/duct tape/whatever wrapped tight to mostly seal it, then put the air 90psi+ into a hole/slit in the hose & blast away.
Go easier on the heater core, it can't take the volume the others can.
*******
*******
******
Yes, you do get wet, and it isn't going to get out all the mineral buildup, but that filter BS is a joke.
I used a diving tank with over 1500psi to clean out some deteriorated hose crap from a radiator's upper tank. It probably had enough volume to destroy things, use some judgment/discretion on your stuff!
Pictures? FU!

[iOnic]

Garden hose full on into inlet/outlet, rag/duct tape/whatever wrapped tight to mostly seal it, then put the air 90psi+ into a hole/slit in the hose & blast away.

^ Take pics of results plz.

[Mr Revhead]

Garden hose full on into inlet/outlet, rag/duct tape/whatever wrapped tight to mostly seal it, then put the air 90psi+ into a hole/slit in the hose & blast away.

^ Take pics of results plz.

seconded
Youtube it

[Mr Ree]

hmmmm....

[RS13]

Another quality allencr post!

Don't put 90psi through your cooling system. Most radiator caps release pressure at 15psi, with 6 times that if there was a blockage you'd blow seals and crack plastic.

The cooling system can handle a bit of crap floating around without much issue, those filter things IMO are just a gimmick and would only end up causing a restriction or blockage themselves.

Me personally, I drain coolant, fill with water, run the engine for 10 mins, drain, repeat a couple of times until the water comes out clean, then fill with coolant. Never had a problem. If the radiator is blocked again, flushing with a garden hose won't do much, it really needs the top taken off and lanced properly.

[Mr Revhead]

I can sell you a proper coolant filter if you want.
But if I were you I'd be looking to overhaul the system properly

[Malcolm]

Another quality allencr post!

Don't put 90psi through your cooling system. Most radiator caps release pressure at 15psi, with 6 times that if there was a blockage you'd blow seals and crack plastic.

Sounds like the intention is to use the pressure to blast the water through more forcefully, rather than pressurising the system. I don't think a rag wrapped around a hose is going to hold 90psi.

[RS13]

Another quality allencr post!

Don't put 90psi through your cooling system. Most radiator caps release pressure at 15psi, with 6 times that if there was a blockage you'd blow seals and crack plastic.

Sounds like the intention is to use the pressure to blast the water through more forcefully, rather than pressurising the system. I don't think a rag wrapped around a hose is going to hold 90psi.

Still, would you risk it?

[Malcolm]

I probably would actually

edit: with the other end of the system open, the risk is pretty damn low of pressurising it, even if you've made an awesome seal on the inlet

[RS13]

*shrug* each to their own I guess. Just doesn't seem like a good practice. Maybe if you've got half a clue and are very careful, but I can see guys pulling off a radiator hose and feeding 90psi through it without considering the more delicate parts.

[Grrrrrrr!]

I probably would actually

edit: with the other end of the system open, the risk is pretty damn low of pressurising it, even if you've made an awesome seal on the inlet

I agree with malcolm, if one end of the system is open and you somehow manage to build enough pressure to crack/pop a top tank off all you've done is save the radiator shop some time, 'cause that core is going to need cleaning out properly/replacing.

[Mr Revhead]

Is be more worried about the force than pressure

[Quint]

pressure is force over area :/