hey team..
Who is currently running a 20v head with a later link g4..?
What dizzy are you using? The link is not liking the factory one at all..
4age B/T 20V Dizzy Configuaration for Link G4
Moderator: The Mod Squad
6 posts
• Page 1 of 1
4age B/T 20V Dizzy Configuaration for Link G4
by tsoob » Sun Jul 14, 2013 3:59 pm
Platinum Wheels
15 Parkway Drive
Mairangi Bay
09 486 5317
WHEELS, TYRES & SUSPENSION!
www.platinumwheels.co.nz
15 Parkway Drive
Mairangi Bay
09 486 5317
WHEELS, TYRES & SUSPENSION!
www.platinumwheels.co.nz
-
tsoob - Toyspeed Member
- Posts: 3253
- Joined: Tue Dec 05, 2006 7:37 pm
- Location: 201.1kw on 19psi
by DexGT » Sun Jul 14, 2013 4:16 pm
When I upgraded to the G4 on the starlet I fitted coil on plug(COP) so no dizzy needed , I did keep the base of the dizzy for the pulse/ reset for the timing 
.
I found a place in oz that makes a plate to fit COP to 20v ,actually they make a few bits you might like, have a look http://s-86.com/parts.php
I turned the cap down and made a inset to tidy it up
.
I found a place in oz that makes a plate to fit COP to 20v ,actually they make a few bits you might like, have a look http://s-86.com/parts.php
I turned the cap down and made a inset to tidy it up
EP82 Starlet GT club race car;
best time around Manfield to date : 1:19:91
"Understeer" is when you hit the fence with the front of the car.
"Oversteer" is when you hit the fence with the rear of the car.
"Horsepower" is how fast you hit the fence.
"Torque" is how far you take the fence with you.
best time around Manfield to date : 1:19:91
"Understeer" is when you hit the fence with the front of the car.
"Oversteer" is when you hit the fence with the rear of the car.
"Horsepower" is how fast you hit the fence.
"Torque" is how far you take the fence with you.
- DexGT
- Toyspeed Member
- Posts: 462
- Joined: Sat May 06, 2006 5:57 pm
- Location: wellington
by matt dunn » Sun Jul 14, 2013 5:21 pm
Does not matter if you run the base or the whole thing the settings are ther same for the triggers.
The 20V dist should work perfect on the G4.
Mine does and so does all the other one'si have seen.
Either you have a wiring issue or a trigger setting issue in the program,
or a dud dist.
How have you wired it?
http://www.linkecu.com/support/document ... 4Tooth.pdf
The 20V dist should work perfect on the G4.
Mine does and so does all the other one'si have seen.
Either you have a wiring issue or a trigger setting issue in the program,
or a dud dist.
How have you wired it?
http://www.linkecu.com/support/document ... 4Tooth.pdf
- matt dunn
- Toyspeed Member
- Posts: 7109
- Joined: Fri Sep 12, 2003 1:01 am
- Location: Timaru
by QikStarlie » Sun Jul 14, 2013 5:41 pm
as above 20v stuff works perfect with link. its the same 24tooth and sync setup, as 16v smallport and heaps of other toyota's run.
-
QikStarlie - Toyspeed Member
- Posts: 1110
- Joined: Tue Mar 25, 2003 10:30 pm
- Location: lost..
by TRD_ZERO » Sun Jul 14, 2013 6:59 pm
yeah I run a link g4 atom on my bt and it works fine on the factory dizzy.
Lightning viewtopic.php?t=73689
Previous:
87 mazda etude turbo, 88 Starlet turbo s, 89 trueno GTZ - Thunder, 93 corolla wagon, 92 fxgt
You can sleep when you are dead.
Previous:
87 mazda etude turbo, 88 Starlet turbo s, 89 trueno GTZ - Thunder, 93 corolla wagon, 92 fxgt
You can sleep when you are dead.
-
TRD_ZERO - Toyspeed Member
- Posts: 1077
- Joined: Sun Jul 16, 2006 12:24 pm
- Location: Howick
by tsoob » Wed Jul 24, 2013 3:22 pm
ECU was set to crank not cas for the pickup.
Platinum Wheels
15 Parkway Drive
Mairangi Bay
09 486 5317
WHEELS, TYRES & SUSPENSION!
www.platinumwheels.co.nz
15 Parkway Drive
Mairangi Bay
09 486 5317
WHEELS, TYRES & SUSPENSION!
www.platinumwheels.co.nz
-
tsoob - Toyspeed Member
- Posts: 3253
- Joined: Tue Dec 05, 2006 7:37 pm
- Location: 201.1kw on 19psi
6 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 31 guests