Ive recently bought a replacement ECU for my AE101 GTZ, and while installing it I can't seem to get to the bolts holding the original ECU in place. The bolts Im talking about are the ones on the drivers side where the drivers foot rest is. There is only about 2.5cm gap between the bolt and the plastic foot rest thingy which isnt enuff to fit the wrench in between.
Can anyone give me some advice on how to get around this problem or how to remove that foot rest?
Cheers.
PS: Thnx Mr Revhead for souricing the ECU & speedy delivery.
Changing ECU
Moderator: The Mod Squad
9 posts
• Page 1 of 1
-
Andy from the block - Toyspeed Member
- Posts: 504
- Joined: Sun Apr 27, 2003 10:51 pm
- Location: North Shore , Auckland
-
MetalupYoAss - Toyspeed Member
- Posts: 804
- Joined: Thu May 16, 2002 9:57 am
- Location: Lake Pukaki (Under the trees)
by Andy from the block » Sat Apr 24, 2004 7:12 pm
the dash around the ECU is already removed...need to remove foot rest to get to bolts....
-
Andy from the block - Toyspeed Member
- Posts: 504
- Joined: Sun Apr 27, 2003 10:51 pm
- Location: North Shore , Auckland
by AceSniper » Sun Apr 25, 2004 10:46 am
can be done with a socket if you angle it right, or just use an old fashan spaner... once the bolts are off on each side unplug it and it just slides out the drivers side 
-
AceSniper - Toyspeed Member
- Posts: 2002
- Joined: Sun Aug 04, 2002 10:55 am
- Location: Hamilton
by Twolitre » Sun Apr 25, 2004 8:14 pm
AceSniper wrote:can be done with a socket if you angle it right, or just use an old fashan spaner... once the bolts are off on each side unplug it and it just slides out the drivers side
Yeah I would've just suggested using a spanner as well, what are they 10/12mm ?
Shouldn't be too hard with the right tools.
-
Twolitre - Toyspeed Member
- Posts: 1896
- Joined: Wed May 15, 2002 4:43 pm
- Location: Sydney/Auckland
by KinLoud » Mon Apr 26, 2004 8:26 am
The footrest is held in place by 2 plastic screws.
Look at the footrest, you will see 2 circles with a grip pattern that looks just like the rest of the footrest. These circles are the screws... get a big screwdriver and undo the screws using the blade of the screwdriver in between the grip pattern. You can then remove the footrest - I had to do this a couple of months ago and it had me puzzled for a bit too.
Ken
Taupo
021 408 863
Look at the footrest, you will see 2 circles with a grip pattern that looks just like the rest of the footrest. These circles are the screws... get a big screwdriver and undo the screws using the blade of the screwdriver in between the grip pattern. You can then remove the footrest - I had to do this a couple of months ago and it had me puzzled for a bit too.
Ken
Taupo
021 408 863
-
KinLoud - ** Moderator **
- Posts: 2893
- Joined: Thu May 16, 2002 7:39 pm
- Location: Auckland
by laserracer » Mon Apr 26, 2004 9:53 am
well done ken i was going to reply but i couldnt think of how to explain those little camoflaged suckers if ya dont look closely ya cant see them
- laserracer
- TS Original Member
- Posts: 167
- Joined: Sun May 19, 2002 11:16 am
- Location: hamilton
-
Andy from the block - Toyspeed Member
- Posts: 504
- Joined: Sun Apr 27, 2003 10:51 pm
- Location: North Shore , Auckland
by Andy from the block » Fri Apr 30, 2004 6:23 pm
I tried screwdriving the plastic screws in a anti-clockwise direction and the footrest still isnt budging! The screws have been spun around anticlockwise in place many many times and dont seem to be going anywhere.
What should I do?
What should I do?
-
Andy from the block - Toyspeed Member
- Posts: 504
- Joined: Sun Apr 27, 2003 10:51 pm
- Location: North Shore , Auckland
9 posts
• Page 1 of 1
Who is online
Users browsing this forum: Bing [Bot] and 61 guests