Toyspeed.org.nz Message Board

by **CEvans** » Thu Aug 18, 2005 6:21 pm

does anyone have a problem with lifter noise in the ae111 blacktop 20v ,is it normal for abit or should it be checked if its getting noisey just asking cause someone told me that 20v were alittle noisier?

by **phatman3801** » Thu Aug 18, 2005 7:04 pm

they dont have lifters... it is quite normal for the vlave clearances to to slightly out whihc creates a ticking noise, u can get it fixed but its not worth it, i got my done and it just slowly came back and it cost a hole heap of money! ifs its not that bad dnt worry bout it

by **Mr Revhead** » Thu Aug 18, 2005 7:15 pm

could be the VVT pulley

My Profile · by **Xavier** » Thu Aug 18, 2005 8:55 pm

is it during cold start or it is always noisy??? if it is always noisy, then it would be like Mr Revhead said, is the VVT pulley... if it is just the cold start and it went away when the engine is warm, it could be ur tensioner...

by **CEvans** » Thu Aug 18, 2005 11:01 pm

its noisey all the time wot does it consist of replacing the vvt pulley and how much?

by **Lloyd** » Thu Aug 18, 2005 11:12 pm

Edited cause I didn't know what I was on about

Sorry, thought they came as a single part

by **Mr Revhead** » Thu Aug 18, 2005 11:16 pm

? wot you on about?

the cam is seperate from the pulley.

iirc around $300 for a new vvt pulley

by **CEvans** » Thu Aug 18, 2005 11:21 pm

k 300 for the pully and how much labour is involved in fitting it?
will engine run better with a new one?
any ideas on who is best for the job in wellington?

by **RedMist** » Fri Aug 19, 2005 9:03 am

CEvans wrote:k 300 for the pully and how much labour is involved in fitting it?
will engine run better with a new one?
any ideas on who is best for the job in wellington?

About an hour, depending on how hard it is to get at the cam covers. You might want to do the cam belt at the same time.
No, in no way will it run better.
Not a clue.

by **Mr Revhead** » Fri Aug 19, 2005 9:18 am

the only way itll go better is if the pulley has jammed. which does happen but is fairly rare

by **CEvans** » Fri Aug 19, 2005 9:24 am

so is it really necessary to replace the vvt pully or wait tile its worn abit more?

by **spencer** » Fri Aug 19, 2005 12:54 pm

tensioner went in a blacktop I had made a violent noise when revved so maybe its the vvt pulley. I could see what it was straight away because rwd and no covers. When the pulleys go is it just the dampening fluid leaks out?

by **Mr Revhead** » Fri Aug 19, 2005 12:57 pm

yeah the fluid leaks out and they sound like a diesel.

by **ROBODISCO_20v** » Sun Aug 28, 2005 1:31 pm

CEvans wrote:does anyone have a problem with lifter noise in the ae111 blacktop 20v ,is it normal for abit or should it be checked if its getting noisey just asking cause someone told me that 20v were alittle noisier?

Could just be a noisy injector, to the untrained ear it could sound like a tappet.

by **TrouserFxGt** » Mon Aug 29, 2005 7:56 am

mine gets noisey injectors every now and then.

Toyspeed.org.nz Message Board

20v lifter noise

20v lifter noise

Re: 20v lifter noise

Who is online