Toyspeed.org.nz Message Board

by **CaldinaGt_t** » Wed Oct 04, 2006 5:14 pm

can it be done, what are the parts needed to do this?

by **NZ_AE86** » Wed Oct 04, 2006 5:27 pm

it can be done.

Details of car here · by **AE85coupe** » Wed Oct 04, 2006 6:13 pm

it can be done

parts:

get a gt4 celica

cut the body off

weld on an AE86 body

or

make a space frame chasis with 4wd and 3sgte running gear, then put an AE86 shell on that

i hope you have disgusting amounts of money to do it though

by **strap-on** » Wed Oct 04, 2006 6:29 pm

no offence but if you have to ask you proabably shouldnt attempt it

Details of car here · by **AE85coupe** » Wed Oct 04, 2006 6:31 pm

strap-on wrote:no offence but if you have to ask you proabably shouldnt attempt it

so very true

if you have to ask about it, the chances of you actually doing it are so so so slim

by **strap-on** » Wed Oct 04, 2006 8:08 pm

like most of my ideas :lol:

Details of car here · by **AE85coupe** » Wed Oct 04, 2006 8:09 pm

strap-on wrote:like most of my ideas

yeah but where would humanity be without people who come up with hair brained schemes???

by **Mr Revhead** » Wed Oct 04, 2006 8:18 pm

no offence but if you have to ask you proabably shouldnt attempt it

thats my line!!!

ill help. come round, bring an ae86, a gt4 and a gas axe

Details of car here · by **AE85coupe** » Wed Oct 04, 2006 8:22 pm

Mr Revhead wrote:
ill help. come round, bring an ae86, a gt4 and a gas axe

hahaha now thats gold (don't forget the welder)

i bet you can pull it off too, sure it may look a little rough, and sure it may not work that well, but hell it will be a 4wd 3sgte ae86 right?? right?....

by **Scotty** » Thu Oct 05, 2006 12:26 am

AE85coupe wrote:
Mr Revhead wrote:
ill help. come round, bring an ae86, a gt4 and a gas axe

hahaha now thats gold (don't forget the welder)

Who need a welder im sure zip ties will hold it :lol:

by **Mr Revhead** » Thu Oct 05, 2006 8:43 am

zip ties can hold rally winners together so a revhead special will go fine with them

by **CaldinaGt_t** » Thu Oct 05, 2006 3:03 pm

why so much, couldnt you just get a St185 Gearbox,ST185 Back end,St185 front end and custom mounts.

by **CaldinaGt_t** » Thu Oct 05, 2006 3:06 pm

look how simple them put a 4WD drivetrain with a 3SGTE in the Toyota Runx and The 2002 shape celica.

by **Punter** » Thu Oct 05, 2006 3:37 pm

Well no it's probably no harder than doing it to any other car.
If you think its simple then do it.

Although would an ae86/5 be wide enough in the engine bay, they wern't designed for a transverse motor

by **NZ_AE86** » Thu Oct 05, 2006 4:39 pm

If I was to do it I would use a North/South layout and use a Subaru Gearbox with a good gearkit.
You would need quite a bit of Fabrication around the front end but it could be done.

by **Adamal** » Thu Oct 05, 2006 4:49 pm

The easiest way to get the bits you need off a GT4:

by **deaf_rattle** » Thu Oct 05, 2006 6:17 pm

wow, a pic of brad without a cast or bandage on.

And the 4wd 3sgte 2000 shape celica, sure its been done....
rod millens work shop did the work. That car has had a shit load of money spent on it. I heard close to a mill, but that seems awfully high.

by **Adamal** » Thu Oct 05, 2006 6:24 pm

deaf_rattle wrote:wow, a pic of brad without a cast or bandage on.

Yes, well then when we went to get the shell back down.... NAAAHHH JUST KIDDING AU!!!!

by **$CENSLS1$** » Fri Oct 06, 2006 10:20 am

Just out of curiousity, why the *uck would you want a 4WD Ae86? :roll:

by **RS13** » Fri Oct 06, 2006 12:46 pm

Hybrid rally car perhaps? But then, you still wouldn't wanna crash it, with the shortage of AE85/86 shells.. if I wanted to spend tens of thousands building something Toyota, with 4WD and 3SGTE, I'd get one of these:

Its' such a shame the base model never came to NZ, one of the nicest looking Corollas IMO!

Toyspeed.org.nz Message Board

AE86 with 3SGTE and 4WD

AE86 with 3SGTE and 4WD

Who is online