Toyspeed.org.nz Message Board

by **thaphatty** » Sat Mar 24, 2007 10:01 pm

Have had this in my garage for a long time now, never known what its been off.

any light much appreciated

suspect za18? or possibly fj20?

by **Adydas** » Sat Mar 24, 2007 10:10 pm

dont hold me to it but looks very simlar to a 4efte manifold just with bigger porting and better design of the tubing.... Its not a 3sgte as there 8-9 studs i belive...

by **Jet_boy01** » Sat Mar 24, 2007 11:25 pm

It does look a bit like a 4efte manifold, but its definately not a standard one, and my 4efte only has two bolts on the bottom side of it, not 3 like that one.

by **RS13** » Sat Mar 24, 2007 11:51 pm

Its' definitely not Z18 or FJ20.

by **summin** » Sun Mar 25, 2007 12:06 pm

Adydas wrote:dont hold me to it but looks very simlar to a 4efte manifold just with bigger porting and better design of the tubing.... Its not a 3sgte as there 8-9 studs i belive...

not 4efte

by **chch34** » Sun Mar 25, 2007 1:59 pm

haven't hks come along way since that was built!! :lol:

by **Jet_boy01** » Sun Mar 25, 2007 2:01 pm

I think that says HK8 not HKS mate...

by **Adydas** » Sun Mar 25, 2007 2:35 pm

i said i wasnt sure but it looks awfully close based on number of studds, My guess would be its a 4a, 4e type motor. 1300-1600

by **Adamal** » Sun Mar 25, 2007 4:07 pm

The spacing between piping suggests something SOHC or pushrod. Can't say I've seen a DOHC engine with spacing like that

by **IH8TEC** » Sun Mar 25, 2007 5:07 pm

Jet_boy01 wrote:I think that says HK8 not HKS mate...

look closer :wink:

the ends are not joined to make an 8.

by **ee904age** » Sun Mar 25, 2007 6:18 pm

Not that it means that much but notice the "Nissan Motor" Casting on the turbo. Guessing it aint Toyota

by **Flunk** » Sun Mar 25, 2007 7:08 pm

ee904age wrote:Not that it means that much but notice the "Nissan Motor" Casting on the turbo. Guessing it aint Toyota

ive got nissan turbos in my toyotas.. doesnt realy mean a thing.

by **chch34** » Sun Mar 25, 2007 9:07 pm

IH8TEC wrote:
Jet_boy01 wrote:I think that says HK8 not HKS mate...

look closer the ends are not joined to make an 8.

Oh na i think it is an 8 :oops:

by **slonlo** » Sun Mar 25, 2007 9:48 pm

might be a crappy honda 2L

b20a3 engine
12-valve, SOHC
dual carb
88 - 90 prelude s (super low spec)

http://www.the-best-source.com/partsCat ... om/catalog

Show me the mud!!! · by **Elmo** » Sun Mar 25, 2007 9:54 pm

that gasket doesnt look anything like that manifold

by **Jet_boy01** » Sun Mar 25, 2007 10:07 pm

Thats just the metal cut out of the gasket though, the exhaust holes look like the same, and the bolts are all in the same places, same amount etc, could be on to a winner there...

by **Adamal** » Sun Mar 25, 2007 11:54 pm

chch34 wrote:
IH8TEC wrote:
Jet_boy01 wrote:I think that says HK8 not HKS mate...

look closer the ends are not joined to make an 8.

Oh na i think it is an 8

by **thaphatty** » Sun Mar 25, 2007 11:55 pm

Jet_boy01 wrote:Thats just the metal cut out of the gasket though, the exhaust holes look like the same, and the bolts are all in the same places, same amount etc, could be on to a winner there...

yerr.. does look alot like it.

but if thats the case then how far off K series is it?

will get some dimensions tomorrow night. manifold is narrower than a 4ag though

Dunno if HKS would make a manifold to suit some crap low end honda motor?

by **chch34** » Mon Mar 26, 2007 8:59 am

it is too! As i said, havent they come a long way!! :lol:

by **4EFTE** » Mon Mar 26, 2007 4:21 pm

what sort of turbo is that ?

Toyspeed.org.nz Message Board

wtf is this exhaust manifold off?

wtf is this exhaust manifold off?

Who is online