Toyspeed.org.nz Message Board

by **Paulio** » Tue Aug 11, 2009 1:27 pm

Hey,

I wana have a play 'round with an e51 box that I have, does anyone have or know where a manual may be, or some basic instructions?

Havnt played with gearboxes much as im not in to that sort of work, but am keen to get in to it.

Any help appreciated.

Paulio

by **gasman** » Tue Aug 11, 2009 1:44 pm

When I pulled mine apart for the first time I used a ae92 repair manual which had a overhaul section for the c52 box and it was almost identical apart from a few locational items.

by **Mr Revhead** » Tue Aug 11, 2009 2:46 pm

have a search on toymods
someone there was translating the manual

no grip · by **Akane** » Tue Aug 11, 2009 4:13 pm

If it's anything like the MR2 box that I had, then you'll need to take the end section cover off, and use a 5th gear puller tool, then take out the casing, PITA tbh.

by **Bazda** » Tue Aug 11, 2009 5:12 pm

Its the same as a MR2 box, only thing different is the shifter.

Ideally you need 2 pullers. A gear puller and jaw pullers.
12mm socket
14mm socket
5mm allen key
24mm socket
big cresent
30mm socket and rattle gun
pliers
hammer
c-clip removers

5th gear can be quite difficult to install back on, for a first timer it would drive you crazy.

by **Paulio** » Tue Aug 11, 2009 5:54 pm

Thanks guys, barry. Very good.

May invest in some pullers tomorrow then, everything else I have. Ill get 5th gear off and see how it goes after that.

Paulio

by **gasman** » Tue Aug 11, 2009 7:43 pm

Bazda wrote:5th gear can be quite difficult to install back on, for a first timer it would drive you crazy.

Big hammer, or even bigger hammer usually works

by **Bazda** » Tue Aug 11, 2009 8:06 pm

gasman wrote:
Bazda wrote:5th gear can be quite difficult to install back on, for a first timer it would drive you crazy.

Big hammer, or even bigger hammer usually works

I mean for aligning the syncro and snycro hub with the clip.

by **AceSniper** » Tue Aug 11, 2009 8:54 pm

just sore this it could be of some help to you....

http://www.snimoc.com/LSDTransmission.html

by **Paulio** » Tue Aug 11, 2009 9:30 pm

Sweet find, cheers bro!

P

by **85AW20v** » Tue Aug 11, 2009 11:20 pm

This might help you out too.....

http://www.ae92gts.com/ae92gts_trans_rb_1.html

by **Paulio** » Fri Sep 04, 2009 1:02 pm

Barry what are the pullers you use? i have tried 2 so far and they dont fit.. first was a 6" 3 arm that was dreaming and the second is a (called usa type) 3" 2 arm on a horizontal bar but the heels on the feet are too fat to allow it to fit in the grove on the gear.. I could grind the heels down but that would compromise the strength of the ankles, if you get what I mean.
im getting jonesway tools btw, bnt is the only place round here that has a range of pullers to order in.

cheers!

by **Bazda** » Fri Sep 04, 2009 1:54 pm

One of these sets for the small gear by it self.
Used the top left hand gripper thingy

by **Paulio** » Fri Sep 04, 2009 2:26 pm

Lol I shouldnt have asked.

Dare I ask how much and where from?

by **Bazda** » Fri Sep 04, 2009 2:50 pm

Paulio wrote:Lol I shouldnt have asked.

Dare I ask how much and where from?

Those ones there are from sulco, the ones I use are a cheaper brand, no idea where they are from though..

by **AceSniper** » Fri Sep 04, 2009 7:26 pm

top left is a bearing separator

On c series I use a harmonic balancer puller to remove 5th syncro hub
and a cheap $20? 3jaw puller from supercheap with the heal ground down haven't had any strength issues just make sure your pulling off square

Toyspeed.org.nz Message Board

Opening e51 box.

Opening e51 box.

Who is online