Toyspeed

Hi guys

Anyone in Auckland/northshore used techstream or able to get there hands on one?
ive got alot of stuff to recalibrate/trouble shoot etc and if i go to toyota/lexus its gonna cost a shit load, car is currently not moving and stuck in back of garage.

hi guys

anyone here worked on a gs460 or a 1urfse engine?
ive put the 1urfse engine and box, wiring etc in my project, and when i power it up the dash doesnt registr what gear its in, so it doent show its in ppark, so it wont start, any one got wiring diagrams or anything???

cheers

Hows this for a do up

small amount of rust




if ya keen let me know

^ Maybe he has a C series or other bell housing which can fit S series engines. Knowing what it came off wouldn't help him find out whether it fits an S and if so whether it positions the engine upright or angled.

Never know.

Exactly, I have a bell, and i know what its off, i want to check if ...

Hi Guys

Any one in aucks got a S series engine thats out of there car? fwd or rwd, i just got a bell i need see if it fits up to the engine

Cheers

check this one out
this is the GASKET KIT, AUTOMATIC TRANSMISSION OVERHAUL for a CR38
using the new parts cross-reference all these vehicles use the same kit, so i would image, youll find any of these autos will bolt straight in
http://www.toyodiy.com/parts/xref?s=043 ... J=on&mG=on

easiest thing to do would be to swap out the auto, most wreckers are giving away a free auto with the 1uz they sell

check it out
all the cars take the same gasket kit for the auto
Hiace http://www.toyodiy.com/parts/p_J_1995_T ... _3501.html
Estima http://www.toyodiy.com/parts/p_J_1992_T ... _3501.html
Liteace http://www.toyodiy.com/parts/p_J_1995_T ... _3501.html
Chaser http://www.toyodiy.com/parts/p_J_1992_T ... _3501.html
Celsior http://www.toyodiy.com/parts/p_J_1995_T ... _3501.html

i couldnt find the cr39, only the cr38, so im assuming must be virtually the same, here show the g/box 2wd and 4wd http://www.toyodiy.com/parts/p_J_1995_T ... _3301.html
and here is the transfer http://www.toyodiy.com/parts/p_J_1995_T ... _3609.html as you can see the gasket is 36143 and the hiace http://www.toyodiy.com/parts/p_J_1995_T ... _3609.html has the same one too

i put a giant screw driver against the flywheel in the teeth and that seems to hold it fine.

looking at toyodiy.co the litace and the hiace both have the same transfer case, so it should just be matter of swapping out the auto with a manual. should be fairly straight forward. youll just need to get linkages for the stick, bell to match, fly etc.
but as i said youll find most autos should ...

you should be able to put inplace an auto from the other larger toyota etc.
when they put a 1uz into the 4wd hilux, they use the 1uz auto, unbolt the tail shaft housing, and bolt it to the 4wd bit. from my understanding, you just have to cut the very end of the 2wd tailshaft to get it to fit, so in ...

get one from a van from a wrecker.
the resivor on a master is held on by a massive hollow bolt from memory, you just unscrew it and lift off the rsovir, all vans ive seen have a remote resivor, you just get the banjo bolt from that master and screw it in,
easy as.

is that a 2wd or 4wd hilux? i put 2jzge into both, 2wd is eay, but 4wd needs custom sump or body raise of 3"(this is what i did), manual or auto? if manual, youll need a fly and all that, unless you find an engine complete, andthen an adaptor plate or genuine/copied/cast bell. also no mods to the ...

none of the pipes are crushed or bent
i am thinking it is blocked aswell, so ill put compressed airthru it today to try clear it

okay
has 3rd master cylinder(this one is off my car and works fine)
brand new wheel cylinders
bias valve from my other surf(was working mint in that surf)
but rear brakes still dont work
only thing i can think of is that its the brake shoes?
but the hand brake works mints, which means the ...

if put a 2jzge into a 91 surf, ln130, had 2.4diesel turbo.
i did a body lift of 3.5" so i didnt have to modify the sump to fit around the diff head.
youll need to find out what the tag says your gearbox is, as there are 2 types of boxes, R153F or something, youll need to measure your bell housing ...

tradeparts on wairau rd, do balancing and machining of the fly wheel. take your flywheel in there with your pressure plate(if you already have, or buy one from them) and get it machined and balanced, machining is only $50, and they normally have to check the balancing when they machine it, otherwise ...

not far, i pushed the pedal a few times(not to the floor tho) as ive done that to wheel cylinders before, the shoes moved out more than enough, and ive adjusted them so there quite tite to get the drums back on.
but there is no leaking of fliud from the wheel cylinders (or anywhwere), wouldnt that ...

yip, hand brake works fine, locks up sweet as

when i had the drums off, i pumped brakes and the shoes moved out, and then sprung back when foot was lifted off the pedal.
the bias valve doesnt have a bleed nipple. just pipe in and pipe out, my other chassis has a bleed nipple on the bias, but that has 2 in(front and rear), and one out, my yn57 ...