Toyspeed.org.nz Message Board

by **GTCRSHR** » Wed Feb 08, 2006 3:29 pm

me up some wheel adaptors/spacers ?

im after 4x100 to 4x 100 with a width of 40mm

by **Ako** » Wed Feb 08, 2006 3:49 pm

Well good effort on making everyone look at your posts :lol:

by **GTCRSHR** » Wed Feb 08, 2006 4:20 pm

thank you

by **Andy7447** » Wed Feb 08, 2006 4:46 pm

yea i kan if you want to send me some plate or i supply

by **THA SHZ** » Wed Feb 08, 2006 6:28 pm

hey chris pm evil si and he will be able to help u out dude

by **Adamal** » Wed Feb 08, 2006 7:31 pm

THA SHZ wrote:hey chris pm evil si and he will be able to help u out dude

Yea, Evil Si is a man with talent.

by **GTCRSHR** » Sat Feb 11, 2006 1:55 pm

any one else ?

by **cr1mnl** » Sat Feb 11, 2006 4:20 pm

Adamal wrote:
THA SHZ wrote:hey chris pm evil si and he will be able to help u out dude

Yea, Evil Si is a man that loves goats.

agreed

by **THA SHZ** » Sun Feb 12, 2006 5:04 pm

cr1mnl wrote:
Adamal wrote:Yea, Evil Si is a man that loves goats.

agreed

haha niceone brad , do u still have the photos of him and that goat up on the mountain ? :lol:

by **vvega** » Sun Feb 12, 2006 6:34 pm

GTCRSHR wrote:any one else ?

yeap
v

by **GTCRSHR** » Sun Feb 12, 2006 6:36 pm

vvega wrote:
GTCRSHR wrote:any one else ?

yeap
v

you can ?

im just waiting to hear back from evil_si and see what he can come up

by **vvega** » Sun Feb 12, 2006 6:37 pm

yeap get back to me when ever

v

by **GTCRSHR** » Thu Feb 16, 2006 7:06 pm

Bump, any one else

do people not want money :?:

by **astrae** » Thu Feb 16, 2006 7:24 pm

GTCRSHR wrote:me up some wheel adaptors/spacers ?

im after 4x100 to 4x 100 with a width of 40mm

I've just got 5mm spacers installed and certed. The law says you can only have upto 20mm.

you doing it legally?

Quote from http://www.lvvta.org.nz/Wheels&Tyres.pdf wrote:2.5 WHEEL SPACING AND ADAPTION REQUIREMENTS

Spacer requirements for all wheels

2.5(1) A wheel spacer fitted to a low volume vehicle between the wheel
and hub assembly, other than that fitted as original equipment by
a high volume vehicle manufacturer, must:

(a) have a maximum spacing of each wheel away from the hub
surface of 20 mm;and

(b) be set-screwed or attached by another secure method to either
the wheel or hub face; and

(c) be manufactured from a solid block of suitable material;and

(d) have two machined or die-cast surfaces that are parallel, and
contain minimal indentations or irrgularities; and
(e) be fitted as to ensure the wheel locates snugly over the hub
spigot so that the hub carries the weight of the wheel assembly
instead of the wheel studs, or were there is a mis-match
between the hub spigot and the wheel centre, a close tolerance
fit center bore locator must be provided;and

(f) maintain, with the spacer fitted, not less than the minimum
required amount of wheel stud or bolt engagement specified
in 2.4(4)

by **GTCRSHR** » Thu Feb 16, 2006 8:12 pm

well i was hoping to ...

but after reading that doesnt seem like i can get it certed ...

cheers for that time to have a bit of a rethink

Does any one have any alternative ideas?

by **soopachargen** » Thu Feb 16, 2006 8:25 pm

what about keeping the 20mm but going to a different stud pattern?? say something rear wheel drive so that u have a wider range of offsets available?? I'm guessing through your past posts that you've widebodied your corolla and need wheels to fill the guards?

by **GTCRSHR** » Thu Apr 20, 2006 4:43 pm

hi guys,

this guy is the person you want to deal with in regards to spacers /adapters

http://www.trademe.co.nz/Members/Listin ... ber=494852

mine arrived today, very happy

Toyspeed.org.nz Message Board

Who here can machine... NOW WITH QUESTION

Who here can machine... NOW WITH QUESTION

Re: Who here can machine...

Who is online