quick question, i searched not quite the answers i needed tho
silvertop 20v extractors?
will they fit a gze?
do i need the 20v 2-1 section also, or will they bolt up to the gze 2-1 section?
does it have a o2 sensor port???
cheers
extractors
Moderator: The Mod Squad
11 posts
• Page 1 of 1
extractors
by bluemaumau » Thu Apr 27, 2006 11:58 pm
4AGTE AE101 COROLLA - 90%
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
-
bluemaumau - Toyspeed Member
- Posts: 4087
- Joined: Sun Oct 16, 2005 7:08 pm
- Location: SYDNEY, NSW
by no_8wire » Fri Apr 28, 2006 12:05 am
1. yes will fit, need to slot the two outside holes.
2. yes, unless you make a custom 2-1 section ( as this is were the o2 sensor is on 20V)
3. As above o2 sensor is 2-1 section bit on the 20V
2. yes, unless you make a custom 2-1 section ( as this is were the o2 sensor is on 20V)
3. As above o2 sensor is 2-1 section bit on the 20V
-
no_8wire - Toyspeed Member
- Posts: 2268
- Joined: Thu Dec 30, 2004 7:30 pm
by Caveman » Fri Apr 28, 2006 7:59 am
no_8wire wrote:1. yes will fit, need to slot the two outside holes.
2. yes, unless you make a custom 2-1 section ( as this is were the o2 sensor is on 20V)
3. As above o2 sensor is 2-1 section bit on the 20V
Are you sure the dont collide with the cas?
-
Caveman - Toyspeed Member
- Posts: 1918
- Joined: Sun Sep 12, 2004 11:20 am
- Location: West Auckland
by Adamal » Fri Apr 28, 2006 8:25 am
Cas????
I put Silvertop extractors on my Bluetop (Cheers no_8wire!) and they go fine. The do need modding, but it was already done for me.
But yea, the 2 - 1 flange on the 16v has slightly more spacing between the pipes.
The hole for the O2 sensor is quite far from the 2 - 1 flange as well..... Its almost right next to the end of it. Quite a distance from the original O2 sensor in the 16v extractors.
I put Silvertop extractors on my Bluetop (Cheers no_8wire!) and they go fine. The do need modding, but it was already done for me.
But yea, the 2 - 1 flange on the 16v has slightly more spacing between the pipes.
The hole for the O2 sensor is quite far from the 2 - 1 flange as well..... Its almost right next to the end of it. Quite a distance from the original O2 sensor in the 16v extractors.
Motorsport is like sex. You could take it to track and have a long, enjoyable session, or you could take it to the strip and get it over with in less than 20 seconds.
-
Adamal - Toyspeed Member
- Posts: 11592
- Joined: Sun May 02, 2004 4:01 pm
- Location: Waitakere Drift Stage (Ranges)
by bluemaumau » Fri Apr 28, 2006 8:02 pm
hmm thanks guys, is it just a case of lengthening the wire (o2) then?
4AGTE AE101 COROLLA - 90%
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
-
bluemaumau - Toyspeed Member
- Posts: 4087
- Joined: Sun Oct 16, 2005 7:08 pm
- Location: SYDNEY, NSW
by Caveman » Sat Apr 29, 2006 1:54 am
4AGZE has a different cam angle sensor. It collides with the coby N/A 16V extractors. Just check for clearence. If the pipe comes straight off cylinder 1 then it probably wont fit without hammering the pipe.
-
Caveman - Toyspeed Member
- Posts: 1918
- Joined: Sun Sep 12, 2004 11:20 am
- Location: West Auckland
by bluemaumau » Sat Apr 29, 2006 7:12 am
1998 wrote:4AGZE has a different cam angle sensor. It collides with the coby N/A 16V extractors. Just check for clearence. If the pipe comes straight off cylinder 1 then it probably wont fit without hammering the pipe.
nah bro im talking about 20v standard extractors
4AGTE AE101 COROLLA - 90%
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
-
bluemaumau - Toyspeed Member
- Posts: 4087
- Joined: Sun Oct 16, 2005 7:08 pm
- Location: SYDNEY, NSW
by Caveman » Sun Apr 30, 2006 3:10 am
bluemaumau wrote:1998 wrote:4AGZE has a different cam angle sensor. It collides with the coby N/A 16V extractors. Just check for clearence. If the pipe comes straight off cylinder 1 then it probably wont fit without hammering the pipe.
nah bro im talking about 20v standard extractors
Yea I know that
I just know for sure it collides with coby extractors, might do on the 20V ones too, but maybe not 
Turbo manifold ftw
-
Caveman - Toyspeed Member
- Posts: 1918
- Joined: Sun Sep 12, 2004 11:20 am
- Location: West Auckland
by bluemaumau » Sun Apr 30, 2006 9:55 am
1998 wrote:bluemaumau wrote:1998 wrote:Turbo manifold ftw
4AGTE AE101 COROLLA - 90%
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
Where the $&#$% is that oil leak coming from /club
looking for enkei RP01 center caps (white)
-
bluemaumau - Toyspeed Member
- Posts: 4087
- Joined: Sun Oct 16, 2005 7:08 pm
- Location: SYDNEY, NSW
by soopachargen » Mon May 01, 2006 4:53 pm
powersteering pump also proves to be a problem being in a different spot on the gze
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
11 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 6 guests