which wire do i splice on my cluster to get my tacho working again?
EDIT:: haha its an ae92 trueno running a link ecu
ae92 dash tacho wiring
Moderator: The Mod Squad
10 posts
• Page 1 of 1
ae92 dash tacho wiring
by SpeedRacer » Fri Jan 05, 2007 8:16 pm
hey,
which wire do i splice on my cluster to get my tacho working again?
EDIT:: haha its an ae92 trueno running a link ecu
which wire do i splice on my cluster to get my tacho working again?
EDIT:: haha its an ae92 trueno running a link ecu
Last edited by SpeedRacer on Sat Jan 06, 2007 7:35 pm, edited 1 time in total.
Sinister Sleeper 35
-
SpeedRacer - Toyspeed Member
- Posts: 407
- Joined: Tue Apr 12, 2005 10:30 am
- Location: Palmy
by SpeedRacer » Sat Jan 06, 2007 6:20 pm
bump
even if some one could tell me how to figure out which one it is?
even if some one could tell me how to figure out which one it is?
Sinister Sleeper 35
-
SpeedRacer - Toyspeed Member
- Posts: 407
- Joined: Tue Apr 12, 2005 10:30 am
- Location: Palmy
by soopachargen » Sat Jan 06, 2007 6:35 pm
is it a non gze dash with a gze twin coil setup??
When in doubt, down and out.
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
"This is the Internet, it has no sympathy and shows no mercy. It feeds on weakness and preys on sensitivity. It will e-kill you at the first opportunity. Be brave or be e-dead." - NZHONDAS
-
soopachargen - Toyspeed Member
- Posts: 1598
- Joined: Thu Aug 05, 2004 1:54 pm
- Location: Silverdale
by SpeedRacer » Sat Jan 06, 2007 6:55 pm
nope just a standard gt apex with dizzy
Sinister Sleeper 35
-
SpeedRacer - Toyspeed Member
- Posts: 407
- Joined: Tue Apr 12, 2005 10:30 am
- Location: Palmy
by matt dunn » Mon Jan 08, 2007 7:36 pm
SpeedRacer wrote:also is a tacho essential for dyno?
not with a link as the will just get rpm off the hand controller or laptop they will use.
Depends on how it is wired.
If they have used most of the OE loom and just adapted on the link and igniter etc etc onto the appropiate places in the loom,
( which is quite likely)
the easiest place is just go to the old igniter wiring.
There would have originally been 5 wires, and now they will only be using 3 or maybe 2 as none of the 5 are earth.
You need to join the one that was labelled EXT on the old igniter and join it to the coil -ve.
OR failing that run a wire from the IG- in the diagnostic socket to the coil -ve.
Matt
- matt dunn
- Toyspeed Member
- Posts: 7109
- Joined: Fri Sep 12, 2003 1:01 am
- Location: Timaru
by SpeedRacer » Mon Jan 08, 2007 8:30 pm
ok, wiring in engine bay is completely new. also will having no cluster affect starting? becasue now it wont start 
Sinister Sleeper 35
-
SpeedRacer - Toyspeed Member
- Posts: 407
- Joined: Tue Apr 12, 2005 10:30 am
- Location: Palmy
10 posts
• Page 1 of 1
Who is online
Users browsing this forum: Bing [Bot] and 11 guests