Toyspeed.org.nz Message Board

by **sark.inc** » Thu Nov 05, 2009 5:58 pm

Do the flywheels on the 4afe and 4age match up?

silvertop.

by **bluemaumau** » Thu Nov 05, 2009 5:58 pm

4afe 6 bolt
4age 8 bolt

by **sark.inc** » Thu Nov 05, 2009 6:00 pm

Well, now i need to buy a 4age flywheel :E

by **Trls250s** » Thu Nov 05, 2009 6:26 pm

sark.inc wrote:Well, now i need to buy a 4age flywheel :E

I have a spare 20v one i would be willing to part with. PM me

by **sark.inc** » Thu Nov 05, 2009 7:51 pm

There is something else i know it.... damn it what am i forgetting?!?!?!

by **shihad** » Fri Nov 06, 2009 11:45 am

arnt early 4age bluetops 6 bolt

red car · by pc » Fri Nov 06, 2009 12:06 pm

shihad wrote:arnt early 4age bluetops 6 bolt

All 8 bolt.

by **headshotnz** » Fri Nov 06, 2009 9:11 pm

So i got my levin on the road.
I dumbly enough forgot to check the oil (also have stuffed rings) went around some tight corners (some what fast... ), what i believe has happened is the very little remaining oil has moved to one side, resulting in my car left with a nice ticking sounds/ also car doesnt want to rev over 4-5ish rpm.

I also unplugged the VVT solinoid and it made no difference to the ticking, also the idle didnt change and the car felt no different to drive.

The ticking sounds like its coming from cylinder number 4 side, and up in the head region, apposed to the block.

Does any one know exactly what it is? first guess was siezed bottom end bearing.

Website · by **Bling** » Fri Nov 06, 2009 9:24 pm

So any oil in it?

by **Mr Revhead** » Fri Nov 06, 2009 9:35 pm

ticking? or knocking?

by **MR2BOY23** » Fri Nov 06, 2009 9:57 pm

bottom end bearing wont make a knocking ticking noise as far as I know

by **sergei** » Fri Nov 06, 2009 10:30 pm

Essdub23 wrote:bottom end bearing wont make a knocking ticking noise as far as I know

It will, if there is enough play to touch valve/head.

by **AE25** » Sun Nov 15, 2009 10:38 pm

i would be pulling oil filter off and chop it in half.. see if there's any bearing material in it.
don't suppose you have an oil pressure guage fitted? is it lower than normal at idle?

by **Truenotch** » Sun Nov 15, 2009 11:02 pm

Sounds to me like you have run a big end bearing....

by **sark.inc** » Tue Nov 17, 2009 7:27 pm

Well just got a flywheel off endless spares, 75$ and it was machined!

by **B_giB** » Wed Nov 18, 2009 7:31 am

Good guys those Endless spares guys...

My cousin is the owner lol

by **Flannelman** » Wed Nov 18, 2009 5:27 pm

If there is enough play in the berring so the piston can touch the valves, no one will here it above the knocking of the conrod against the crank.

Mine gets rattly in the valve gear when its low on oil, especialy at idle. Change the oil and fill with 20-50

by **sark.inc** » Sat Nov 21, 2009 11:52 am

Does anyone have pictures of vacuum lines and such for the 4age silver?

I need to get some!!

Toyspeed.org.nz Message Board

4AGE question

4AGE question

20v ticking qusetion

Who is online