Toyspeed.org.nz Message Board

Toyota Club of New Zealand Message Board

Skip to content

Exedy clutch problems

The place for all technical car discussions. If you haven't already, read our Disclaimer first!

Moderator: The Mod Squad

Post a reply

Postby eskimo » Tue Nov 30, 2010 11:21 am

Ive had problems with them slipping from out of the box as well & they didnt want a bar of it so cut my losses and wont be buying another one ever again.
"If in doubt, flat out" Colin McRae 1968-2007
Current:2003 Legacy 3.0R Spec B
Previous: ST185 GT4, SW20 MR2, ST206 Curren, AE111 Corolla GT
User avatar
eskimo
Toyspeed Member
 
Posts: 787
Joined: Wed Sep 13, 2006 12:55 am
Location: Auckland
Top

Postby Tagged » Tue Nov 30, 2010 11:34 am

thanks for the detailed image and replies!
looks like exedys got some issues.....
User avatar
Tagged
Toyspeed Member
 
Posts: 343
Joined: Mon Oct 11, 2010 11:01 am
Location: Christchurch
Top

Postby Adamal » Tue Nov 30, 2010 12:11 pm

They're saying they tested it and it is holding pressure as it should. I might take it somewhere else along with my old pressure plate and get the both tested
Last edited by Adamal on Tue Nov 30, 2010 12:17 pm, edited 1 time in total.
Motorsport is like sex. You could take it to track and have a long, enjoyable session, or you could take it to the strip and get it over with in less than 20 seconds.
User avatar
Adamal
Toyspeed Member
 
Posts: 11592
Joined: Sun May 02, 2004 4:01 pm
Location: Waitakere Drift Stage (Ranges)
Top

Postby shihad » Tue Nov 30, 2010 12:14 pm

in my experience and everyone I know exedy never had a problem. extreme clutchs on the other hand.........
getting bottled by the friendly Oamaru locals for not doing skids - Coupe Life
User avatar
shihad
Toyspeed Member
 
Posts: 769
Joined: Mon Apr 25, 2005 12:02 am
Location: dunedin in the winter gizzy in the summer
Top

Postby ryanfels » Tue Nov 30, 2010 1:02 pm

Ive used a few Exedy clutchs now and ive never had a problem
thegreatestben wrote:It's lucky you arent a douchebag other wise I wouldn't help you :wink: :wink:

mark 2 gx61 2jzgte powered - viewtopic.php?t=72619&start=0
Discussion - viewtopic.php?t=72620
User avatar
ryanfels
Toyspeed Member
 
Posts: 455
Joined: Sun Jun 17, 2007 11:24 pm
Location: West Auckland
Top

Postby Akane » Tue Nov 30, 2010 1:48 pm

Adamal wrote:They're saying they tested it and it is holding pressure as it should. I might take it somewhere else along with my old pressure plate and get the both tested


I think their way of testing it is pushing the springs down with their thumbs and then gives it the green light.
No "stance", no "hellaflush", none of that bullshit. Nothing but no grip on full boost.
http://www.lol.co.nz/ random shit.
User avatar
Akane
Toyspeed Member
 
Posts: 4073
Joined: Tue May 14, 2002 2:08 am
Location: Auckland
Top

Postby Adamal » Tue Nov 30, 2010 7:40 pm

Well, they do have a pressure tester, and it came out the same with my new one as my old one. They said that they think there has been some preload on the bearing causing it to slip, which is bullshit, as you can easily move the fork with your finger and feel it make contact with the diaphragm of the pressure plate.

They said "Hey, we'll give you another one, but it'll do exactly the same thing". Told my mechanic that and he said "Yep, gettit. It'll be fixed tomorrow.".
Motorsport is like sex. You could take it to track and have a long, enjoyable session, or you could take it to the strip and get it over with in less than 20 seconds.
User avatar
Adamal
Toyspeed Member
 
Posts: 11592
Joined: Sun May 02, 2004 4:01 pm
Location: Waitakere Drift Stage (Ranges)
Top

Postby allencr » Tue Nov 30, 2010 8:53 pm

Can you please take a pic or Measurement of the disk & clutch to see the disk thickness and the distance from the flywheel to the pressure plate?

Stepped flywheel with a different level between the friction surface and the pressure plate mount? A rule of thumb is that the distance between the PP's surface and the flywheel should be 1/2 the thickness of the disk.
allencr
Toyspeed Member
 
Posts: 346
Joined: Thu Dec 04, 2008 9:02 am
Location: Talahassee, Florida USofA
Top

Postby Adamal » Tue Nov 30, 2010 9:18 pm

I've already said that its not a stepped surface, its flush :P and I don't have the gear with me, so can't measure it. Clutch plate was about 7.8mm or something though
Motorsport is like sex. You could take it to track and have a long, enjoyable session, or you could take it to the strip and get it over with in less than 20 seconds.
User avatar
Adamal
Toyspeed Member
 
Posts: 11592
Joined: Sun May 02, 2004 4:01 pm
Location: Waitakere Drift Stage (Ranges)
Top

Postby THA SHZ » Wed Dec 01, 2010 11:51 am

never mind we have figured it out , does anyone have a 5 bolt nose cone that sits overtop of the shaft and semi holds the bellhousing to the box ?
Im the Daddy of the Mack Daddys ! :-)

http://toyspeed.blakjak.net/profiles/photos/861.jpg
User avatar
THA SHZ
Toyspeed Member
 
Posts: 2015
Joined: Wed May 12, 2004 5:48 pm
Location: Westside
Top

Postby Adamal » Wed Dec 01, 2010 2:55 pm

Have found one, wrecker is connecting mechanic to confirm that the part number is right. Should be, fingers crossed
Motorsport is like sex. You could take it to track and have a long, enjoyable session, or you could take it to the strip and get it over with in less than 20 seconds.
User avatar
Adamal
Toyspeed Member
 
Posts: 11592
Joined: Sun May 02, 2004 4:01 pm
Location: Waitakere Drift Stage (Ranges)
Top

Postby XS1V » Thu Dec 02, 2010 9:01 am

Better apologize to exedy lol 8)

Brad
Check out our shop http://www.raceandrally.co.nz or follow us on Facebook https://www.facebook.com/RaceRallyDirect

ST205 Group A Rallye #2363
WEEDA - AE82 Rally Car Blacktop
K-AM 703 - Group A Rally Car ST185 TTE Replica
User avatar
XS1V
Toyspeed Member
 
Posts: 1248
Joined: Fri Nov 19, 2004 10:17 am
Location: North Shore, Auckland
Top

Postby Adamal » Thu Dec 02, 2010 10:35 am

XS1V wrote:Better apologize to exedy lol 8)

Brad


Nahh.
Motorsport is like sex. You could take it to track and have a long, enjoyable session, or you could take it to the strip and get it over with in less than 20 seconds.
User avatar
Adamal
Toyspeed Member
 
Posts: 11592
Joined: Sun May 02, 2004 4:01 pm
Location: Waitakere Drift Stage (Ranges)
Top

Postby tsoob » Thu Dec 02, 2010 12:22 pm

Adamal wrote:
XS1V wrote:Better apologize to exedy lol 8)

Brad


Nahh.



LIKE!
Platinum Wheels
15 Parkway Drive
Mairangi Bay
09 486 5317
WHEELS, TYRES & SUSPENSION!
www.platinumwheels.co.nz
User avatar
tsoob
Toyspeed Member
 
Posts: 3253
Joined: Tue Dec 05, 2006 7:37 pm
Location: 201.1kw on 19psi
Top

Postby allencr » Thu Dec 02, 2010 1:11 pm

If it was the bearing retainer tube that is too long & has been keeping it slightly disengaged, I think that the PP's fingers would have been pretty chewed up & nasty looking the first time you removed it. Were they?
allencr
Toyspeed Member
 
Posts: 346
Joined: Thu Dec 04, 2008 9:02 am
Location: Talahassee, Florida USofA
Top

Postby Adamal » Thu Dec 02, 2010 1:32 pm

Not anymore than you'd expect one that comes out to be
Motorsport is like sex. You could take it to track and have a long, enjoyable session, or you could take it to the strip and get it over with in less than 20 seconds.
User avatar
Adamal
Toyspeed Member
 
Posts: 11592
Joined: Sun May 02, 2004 4:01 pm
Location: Waitakere Drift Stage (Ranges)
Top

Postby Bazda » Thu Dec 02, 2010 1:34 pm

meh get a twin plate :D
1988 Toyota Levin GTZ 410kw atw @26psi
Join us on facebook - MRP - Manon Racing Products
http://www.mrpltd.co.nz
Turbonetics|Fortune Auto Coilovers|Wilwood brakes|Tilton clutches|
User avatar
Bazda
Toyspeed Sponsor
 
Posts: 5713
Joined: Sat Jun 01, 2002 10:32 pm
Location: Auckland
Top

Postby Adamal » Thu Dec 02, 2010 1:53 pm

Bazda wrote:meh get a twin plate :D


Believe me, I'd LOVE to!
Motorsport is like sex. You could take it to track and have a long, enjoyable session, or you could take it to the strip and get it over with in less than 20 seconds.
User avatar
Adamal
Toyspeed Member
 
Posts: 11592
Joined: Sun May 02, 2004 4:01 pm
Location: Waitakere Drift Stage (Ranges)
Top

Postby shihad » Thu Dec 02, 2010 2:09 pm

Bazda wrote:meh get a twin plate :D

viewtopic.php?t=81763
LOl he doesn't have 4age thread confusion my bad.
getting bottled by the friendly Oamaru locals for not doing skids - Coupe Life
User avatar
shihad
Toyspeed Member
 
Posts: 769
Joined: Mon Apr 25, 2005 12:02 am
Location: dunedin in the winter gizzy in the summer
Top

Postby THA SHZ » Thu Dec 02, 2010 4:39 pm

allencr wrote:If it was the bearing retainer tube that is too long & has been keeping it slightly disengaged, I think that the PP's fingers would have been pretty chewed up & nasty looking the first time you removed it. Were they?

also depends how long ago they welded it and whether they machined the bearing down to suit or not , our last option is to machine the snout , very last option .
Im the Daddy of the Mack Daddys ! :-)

http://toyspeed.blakjak.net/profiles/photos/861.jpg
User avatar
THA SHZ
Toyspeed Member
 
Posts: 2015
Joined: Wed May 12, 2004 5:48 pm
Location: Westside
Top
PreviousNext
Post a reply

Return to Tech Questions

Who is online

Users browsing this forum: Google [Bot] and 31 guests

Powered by phpBB® Forum Software © phpBB Group
Time : 0.020s | 12 Queries | GZIP : On